Skip to main content

RC jeet plane

 Rc jeet plane

NRF24 2.5GHz data transmission speed. BLDC motor 1000kV max Load 15Amp.

Transmitter or Receiver 

Make transmitter or Receiver previous post check now. Transmitter make just ₹250/- . Transmitter making components NRF24 with antenna module, atmega8A Microcontroller, X-Y axis module with Tap-switch, 3 way-switch, 16.00MHz crystal and 3.3V regulator IC.

  Receiver also use NRF24 without antenna module, atmega 328P, 16.00MHz crystal and 3.3V regulator IC.


Plane Motor ESC

Motor 1000kV brushless DC motor use 10 Inches Propeller or electronic speed controller 30A . 

Microcontroller

Atmega8A 40Pin IC 8KB of programmable memory speed 16MHz 6 PWM pins 23 I/O pins 8bit processor 1KB SRAM, 512 Bytes EEPROM.

Atmega 328P 40Pin IC 32KB of programmable memory speed 16MHz 6 PWM pins and 23 I/O pins 8bit processor.

 

Labels:

Comments

Post a Comment

Don't enter any scam link

Popular posts from this blog

Fm transmitter circuit

Fm transmitter circuit Power supply   :-   Using power supply stable DC voltage 2 V to 3.7 V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components  :- Transistor BC 547 , Resistance 100 ohm , 4.7 K ohm .   Capacitor 1nF, 47pF, 22pF.   Inductor 1uH. Condenser mic any . Resistance  :-   Using resistance 100 ohm +-5% changing 1/3 watt, 4.7 K ohm +-5% changing 1/3 watt. Capacitor  :-   1nF this capacitor number 102 non-polar, 22pF this capacitor number 22 non-polar, 47pF this capacitor number 47 non-polar. Inductor  :-   This part important part for any transmitter circuit, 1uH 5Turn 24SWG. Transistor  :-   BC 547  is an NPN Bipolar junction transistor. It is commonly  used  to amplify current. A small current at its base controls a larger current at collector & emitter terminals.  It has a transition...
11 comments
Read more

Automatic home appliances

 Automatic Home Appliances Remote control electrical appliances  Setting up  IR sensor  connection to Atmega 328P is very simple. Beside VCC and GND  pin , the  sensor  has only one output  pin  that should be connected to one of digital  pins  of the Atmega 328P. HC - 05  has red LED which indicates connection status, whether the  Bluetooth  is connected or not. Before connecting to  HC - 05 module  this red LED blinks continuously in a periodic manner. When it gets connected to any other  Bluetooth  device, its blinking slows down to two seconds. This  module works  on 3.3 V - 6V but you can use only 5V DC. this module use any Serial  AMS1117  is a popular SMD package 3-pin voltage regulator that is available in many models for fixed and adjustable voltage requirements. The IC can deliver a maximum current of 1A and the output voltage can vary from 1.5V to 5V. ...
Post a Comment
Read more

FM transmitter using crystal

FM transmitter using crystal   Power supply   :-   Using power supply stable DC voltage 2 V to 3.7 V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components  :-  Transistor BC 547 , Resistance 100 ohm, 4.7K ohm.   Capacitor 1nF, 47pF,              22pF.   Inductor 1uH. Condenser mic any .       Resistance  :-   Using resistance 100 ohm +-5% changing 1/3 watt, 4.7 K ohm +-5% changing 1/3 watt. Video link -  https://youtu.be/aV7K2NHrHTM 3 Volt Circuit Diagram Capacitor  :-   1uF this capacitor positive pin connect 4.7K ohm resistance one pin and another pin connect 2K ohm resistance one number pin. 5 Volt Circuit Diagram This Circuit Transmitter range 0.3 Kilometre (300 Metre) to 0.5 kilometre (500 Metre) without any obstacle otherwise range 0.2 Kilometre (200 metre) anywhere. It's a spy device. D...
1 comment
Read more