Skip to main content

RC Transmitter Receiver

 RC Transmitter Receiver


This transmission range 1.5KM just 250/-useful components NRF24L01 module with antenna. 

Using microcontroller atmel company

At mega series Atmega8A for Transmitter

For receiver circuit NRF24L01 module without extranal antenna. Using microcontroller for receiver atmel company atmega series Atmega 328P .

Programming upload ISP PIN using Arduino nano you can use ISP tool .

Programming IDE software Arduino IDE , Visual Studio Code or any other software.



NRF24L01 module supply +3.3V constant
Or microcontroller supply +5V constant . Joystick Value 0 to 255 middle value 127 with 0/1 switch.





Full Circuit or Code Comming soon.




Labels:
Location: India

Comments

Post a Comment

Don't enter any scam link

Popular posts from this blog

Fm transmitter circuit

Fm transmitter circuit Power supply   :-   Using power supply stable DC voltage 2 V to 3.7 V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components  :- Transistor BC 547 , Resistance 100 ohm , 4.7 K ohm .   Capacitor 1nF, 47pF, 22pF.   Inductor 1uH. Condenser mic any . Resistance  :-   Using resistance 100 ohm +-5% changing 1/3 watt, 4.7 K ohm +-5% changing 1/3 watt. Capacitor  :-   1nF this capacitor number 102 non-polar, 22pF this capacitor number 22 non-polar, 47pF this capacitor number 47 non-polar. Inductor  :-   This part important part for any transmitter circuit, 1uH 5Turn 24SWG. Transistor  :-   BC 547  is an NPN Bipolar junction transistor. It is commonly  used  to amplify current. A small current at its base controls a larger current at collector & emitter terminals.  It has a transition...
11 comments
Read more

FM transmitter using crystal

FM transmitter using crystal   Power supply   :-   Using power supply stable DC voltage 2 V to 3.7 V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components  :-  Transistor BC 547 , Resistance 100 ohm, 4.7K ohm.   Capacitor 1nF, 47pF,              22pF.   Inductor 1uH. Condenser mic any .       Resistance  :-   Using resistance 100 ohm +-5% changing 1/3 watt, 4.7 K ohm +-5% changing 1/3 watt. Video link -  https://youtu.be/aV7K2NHrHTM 3 Volt Circuit Diagram Capacitor  :-   1uF this capacitor positive pin connect 4.7K ohm resistance one pin and another pin connect 2K ohm resistance one number pin. 5 Volt Circuit Diagram This Circuit Transmitter range 0.3 Kilometre (300 Metre) to 0.5 kilometre (500 Metre) without any obstacle otherwise range 0.2 Kilometre (200 metre) anywhere. It's a spy device. D...
1 comment
Read more

Automatic home appliances

 Automatic Home Appliances Remote control electrical appliances  Setting up  IR sensor  connection to Atmega 328P is very simple. Beside VCC and GND  pin , the  sensor  has only one output  pin  that should be connected to one of digital  pins  of the Atmega 328P. HC - 05  has red LED which indicates connection status, whether the  Bluetooth  is connected or not. Before connecting to  HC - 05 module  this red LED blinks continuously in a periodic manner. When it gets connected to any other  Bluetooth  device, its blinking slows down to two seconds. This  module works  on 3.3 V - 6V but you can use only 5V DC. this module use any Serial  AMS1117  is a popular SMD package 3-pin voltage regulator that is available in many models for fixed and adjustable voltage requirements. The IC can deliver a maximum current of 1A and the output voltage can vary from 1.5V to 5V. ...
Post a Comment
Read more