Make Induction Heater

Make Induction Heater

Video link - https://youtu.be/YlY6zy8DpYo

This circuit use full comments value or comments name.

Using inductor 10uH to 100uH you can use everyone this range or heating inductor coil 5turn use 16SWG to 22SWG I am use 22SWG you can use any of this range.

Using MOSFET Z44 very frist switching

Z44 frequency range 200MHZ to 4GHZ.

Another MOSFET IRF540 I am using this circuit Z44 you can use any of this first switching MOSFET.

Using Diode 2N4007 this is American diode
This frist recover Diode you can use any frist recover Diode like 2N4107.

Using resistance 330 ohm resistance use gate biasing 330 ohm to 470 ohm you can also use this range of resistance.
Using 10K ohms resistance gate pin discharge or noise filter you can use 10K ohm to 20K ohm.

Using capacitor 1.5uF you can use 1.5uF to 20uF range I am using this circuit 1.5uF.

IRFZ44 datasheet this is a third generation Power MOSFET that provide the best combination of fast switching, ruggedized device design, low on-resistance and cost-effectiveness. ... The low thermal resistance and low package cost of the TO-220AB contribute to its wide acceptance throughout the industry.
frequency range from 200 MHz to 4 GHz and a measurement range from 30 mW to 300 W.

Comments

Fm transmitter circuit

Fm transmitter circuit Power supply :- Using power supply stable DC voltage 2 V to 3.7 V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components :- Transistor BC 547 , Resistance 100 ohm , 4.7 K ohm . Capacitor 1nF, 47pF, 22pF. Inductor 1uH. Condenser mic any . Resistance :- Using resistance 100 ohm +-5% changing 1/3 watt, 4.7 K ohm +-5% changing 1/3 watt. Capacitor :- 1nF this capacitor number 102 non-polar, 22pF this capacitor number 22 non-polar, 47pF this capacitor number 47 non-polar. Inductor :- This part important part for any transmitter circuit, 1uH 5Turn 24SWG. Transistor :- BC 547 is an NPN Bipolar junction transistor. It is commonly used to amplify current. A small current at its base controls a larger current at collector & emitter terminals. It has a transition frequency range up to 100 MHz . When using the transistor as a switch, the max cur

Automatic home appliances

Automatic Home Appliances Remote control electrical appliances Setting up IR sensor connection to Atmega 328P is very simple. Beside VCC and GND pin , the sensor has only one output pin that should be connected to one of digital pins of the Atmega 328P. HC - 05 has red LED which indicates connection status, whether the Bluetooth is connected or not. Before connecting to HC - 05 module this red LED blinks continuously in a periodic manner. When it gets connected to any other Bluetooth device, its blinking slows down to two seconds. This module works on 3.3 V - 6V but you can use only 5V DC. this module use any Serial AMS1117 is a popular SMD package 3-pin voltage regulator that is available in many models for fixed and adjustable voltage requirements. The IC can deliver a maximum current of 1A and the output voltage can vary from 1.5V to 5V. It also has a low drop out voltage of 1.3V when operating at maximum current. pin number 1 GND, pin 2 OUTPUT,

MINI ROBOT

Make a mini robot Use resistance - 10K ohms Use variable resistance -10K ohms Use switch - puss on Arduino nano 2.0

Stdi.cloud

Search This Blog