Make MW transmitter Using NE555

Make MW transmitter
Using NE555

Using comments NE555 timer chip 330 ohms, 1K ohms resistance 0.001uF capacitor

Condenser mic and 9V DC power supply.

Power supply :- Using supply only DC stable you can use 9Volt battery and smps supply
And mobile adaptor unfortunately it is no
9Volt but approx 7V max.

NE555 timer chip :- This chip number 1 pin Ground, pin 2 Trigger, pin 3 Output,Pin 4 reset, pin 5 Cout, pin 6 Three, pin 7 discharge, pin 8 VCC. Important notice this chip you cannot supply voltage 9 volt up otherwise timer cheap was burning.
This chip integrated 2 op-amp or 1 SR flip-flop or one NPN transistor and voltage divider. Supply voltage minimum 4 volt up and maximum 10 volt.
Capacitor :- Using capacitor 0.001uF this capacitor number 102.

You can used any condenser mic

MW frequency:- Medium wave is the part of the medium frequency radio band used mainly for AM radio broadcasting. The spectrum provides about 120 channels with limited sound quality. During daytime, only local stations can be received.

Comments

Fm transmitter circuit

Fm transmitter circuit Power supply :- Using power supply stable DC voltage 2 V to 3.7 V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components :- Transistor BC 547 , Resistance 100 ohm , 4.7 K ohm . Capacitor 1nF, 47pF, 22pF. Inductor 1uH. Condenser mic any . Resistance :- Using resistance 100 ohm +-5% changing 1/3 watt, 4.7 K ohm +-5% changing 1/3 watt. Capacitor :- 1nF this capacitor number 102 non-polar, 22pF this capacitor number 22 non-polar, 47pF this capacitor number 47 non-polar. Inductor :- This part important part for any transmitter circuit, 1uH 5Turn 24SWG. Transistor :- BC 547 is an NPN Bipolar junction transistor. It is commonly used to amplify current. A small current at its base controls a larger current at collector & emitter terminals. It has a transition...

Automatic home appliances

Automatic Home Appliances Remote control electrical appliances Setting up IR sensor connection to Atmega 328P is very simple. Beside VCC and GND pin , the sensor has only one output pin that should be connected to one of digital pins of the Atmega 328P. HC - 05 has red LED which indicates connection status, whether the Bluetooth is connected or not. Before connecting to HC - 05 module this red LED blinks continuously in a periodic manner. When it gets connected to any other Bluetooth device, its blinking slows down to two seconds. This module works on 3.3 V - 6V but you can use only 5V DC. this module use any Serial AMS1117 is a popular SMD package 3-pin voltage regulator that is available in many models for fixed and adjustable voltage requirements. The IC can deliver a maximum current of 1A and the output voltage can vary from 1.5V to 5V. ...

FM transmitter using crystal

FM transmitter using crystal Power supply :- Using power supply stable DC voltage 2 V to 3.7 V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components :- Transistor BC 547 , Resistance 100 ohm, 4.7K ohm. Capacitor 1nF, 47pF, 22pF. Inductor 1uH. Condenser mic any . Resistance :- Using resistance 100 ohm +-5% changing 1/3 watt, 4.7 K ohm +-5% changing 1/3 watt. Video link - https://youtu.be/aV7K2NHrHTM 3 Volt Circuit Diagram Capacitor :- 1uF this capacitor positive pin connect 4.7K ohm resistance one pin and another pin connect 2K ohm resistance one number pin. 5 Volt Circuit Diagram This Circuit Transmitter range 0.3 Kilometre (300 Metre) to 0.5 kilometre (500 Metre) without any obstacle otherwise range 0.2 Kilometre (200 metre) anywhere. It's a spy device. D...

Stdi.cloud

Search This Blog