Skip to main content

Fm transmitter by using transistor

      Make FM transmitter by using
Transistor

transistor - bc547
Resistance - 4.7K ohm, 100 ohm.
                                 
 Capacitor - 33PF, 47PF/6.8PF, 1nF.
Inductor coil - 0.1 mH.
Condenser mic
Use battery 3.7V DC

Power supply :- Using power supply stable DC voltage 3.7V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise.

Components :- Transistor BC547, Resistance 100 ohms, 4.7K ohms. Capacitor 1nF, 6.8pF, 33pF. Inductor 1uH. Condenser mic any.

Resistance :- Using resistance 100 ohme +-5% changing 1/3watt, 4.7K ohms +-5% changing 1/3watt.

Capacitor :- 1nF this capacitor number 102 non-polar, 33pF this capacitor number 33 non-polar, 6.8pF this capacitor number 6.8 non-polar.

Inductor :- This part important part for any transmitter circuit, 1uH 5Turn 24SWG.

Transistor :- BC547 is an NPN Bipolar junction transistor. It is commonly used to amplify current. A small current at its base controls a larger current at collector & emitter terminals. It has a transition frequency range up to 100 MHz. When using the transistor as a switch, the max current rating poses a limit on the type of loads that it can drive.

Working :- The FM transmitter is a circuit that uses a very low power to operate and does uses (Frequency Modulation) FM Waves to transmit the sound. With the help of such FM transmitters we can easily transmit the audio signals through the carrier waves with different frequencies. Frist condenser microphone enter voice signal than go to amplification or filter than go to transistor base and transistor switch to activate VCC come out to inductor than generate frequency inductor noise filter 33pF capacitor vcc go through transistor collector to emitter through 100 ohms resistance and transistor collector noise clear through 6.8pF.


FM frequency :- Frequency modulation is the encoding of information in a carrier wave by varying the instantaneous frequency of the wave. The term and technology is used in both

5 turn
In inductor coil

Capacitor number
33PF number - 33
1nF number - 102
47PF number- 47
6.8PF number- 6.8


Inductor coil size
5mm/0.5CM



Comments

Post a Comment

Don't enter any scam link

Popular posts from this blog

Fm transmitter circuit

Fm transmitter circuit Power supply   :-   Using power supply stable DC voltage 2 V to 3.7 V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components  :- Transistor BC 547 , Resistance 100 ohm , 4.7 K ohm .   Capacitor 1nF, 47pF, 22pF.   Inductor 1uH. Condenser mic any . Resistance  :-   Using resistance 100 ohm +-5% changing 1/3 watt, 4.7 K ohm +-5% changing 1/3 watt. Capacitor  :-   1nF this capacitor number 102 non-polar, 22pF this capacitor number 22 non-polar, 47pF this capacitor number 47 non-polar. Inductor  :-   This part important part for any transmitter circuit, 1uH 5Turn 24SWG. Transistor  :-   BC 547  is an NPN Bipolar junction transistor. It is commonly  used  to amplify current. A small current at its base controls a larger current at collector & emitter terminals.  It has a transition...
11 comments
Read more

Automatic home appliances

 Automatic Home Appliances Remote control electrical appliances  Setting up  IR sensor  connection to Atmega 328P is very simple. Beside VCC and GND  pin , the  sensor  has only one output  pin  that should be connected to one of digital  pins  of the Atmega 328P. HC - 05  has red LED which indicates connection status, whether the  Bluetooth  is connected or not. Before connecting to  HC - 05 module  this red LED blinks continuously in a periodic manner. When it gets connected to any other  Bluetooth  device, its blinking slows down to two seconds. This  module works  on 3.3 V - 6V but you can use only 5V DC. this module use any Serial  AMS1117  is a popular SMD package 3-pin voltage regulator that is available in many models for fixed and adjustable voltage requirements. The IC can deliver a maximum current of 1A and the output voltage can vary from 1.5V to 5V. ...
Post a Comment
Read more

FM transmitter using crystal

FM transmitter using crystal   Power supply   :-   Using power supply stable DC voltage 2 V to 3.7 V max. You can only use battery because battery is perfect for this circuit battery output doesn't any noise. Components  :-  Transistor BC 547 , Resistance 100 ohm, 4.7K ohm.   Capacitor 1nF, 47pF,              22pF.   Inductor 1uH. Condenser mic any .       Resistance  :-   Using resistance 100 ohm +-5% changing 1/3 watt, 4.7 K ohm +-5% changing 1/3 watt. Video link -  https://youtu.be/aV7K2NHrHTM 3 Volt Circuit Diagram Capacitor  :-   1uF this capacitor positive pin connect 4.7K ohm resistance one pin and another pin connect 2K ohm resistance one number pin. 5 Volt Circuit Diagram This Circuit Transmitter range 0.3 Kilometre (300 Metre) to 0.5 kilometre (500 Metre) without any obstacle otherwise range 0.2 Kilometre (200 metre) anywhere. It's a spy device. D...
1 comment
Read more